FC6 & iaudio mp3 player (solved?)
Susan Macchia
susan
Sun Dec 31 16:41:24 PST 2006
Well, now I just played around with the sequence of connections and guess what, I got it auto mounted at least. I had to turn the connect the usb cord, turn the iaudio on, *then* conntect the iaudio to the usb. FC6 then (asked first) mounted it on /dev/sde1. So I guess its solved. But I would like to better understand how FC6 handles these devices (as opposed to how it did under FC1).
I have a similar scenario with the Treo 650. When I hit the hotsync, it gets noticed then is unavailable when the sync is done.
Please forgive my ignorance here, but does the newer kernels have hot plugging functionality? And is this why some devices are not noticed unless they are "turned on" in the right order?
--Susan
----- Original Message ----
From: "susan at smacchia.net" <susan at smacchia.net>
To: Linux tips and tricks <linux-users at linux-sxs.org>
Sent: Sunday, December 31, 2006 7:13:30 PM
Subject: Re: FC6 & iaudio mp3 player
Net Llama! <netllama at linux-sxs.org> wrote:
>I'm confused why you're using cdrecord to access a SCSI disk (which is
>basically what your iaudio is).
Because that is what I did under FC1 - I could see all the usb devices
I had hooked up using --scanbus. No so under FC6.
>
>If you insert it (via USB), and check dmesg output, what do you see?
>What is the output from lsusb ?
% lsusb
Bus 002 Device 001: ID 0000:0000
Bus 001 Device 001: ID 0000:0000
Bus 001 Device 004: ID 0c0b:27cb Dura Micro, Inc. (Acomdata) 6-in-1 Flash Reader and Writer
Bus 003 Device 001: ID 0000:0000
Bus 004 Device 001: ID 0000:0000
Bus 005 Device 001: ID 0000:0000
As I said earlier - it isn't detected.
% sg_scan -i
/dev/sg0: scsi2 channel=0 id=0 lun=0 [em] type=0
DMI MultiFlash 3.00 [wide=0 sync=0 cmdq=0 sftre=0 pq=0x0]
/dev/sg1: scsi2 channel=0 id=0 lun=1 [em] type=0
DMI MultiFlash 3.00 [wide=0 sync=0 cmdq=0 sftre=0 pq=0x0]
/dev/sg2: scsi2 channel=0 id=0 lun=2 [em] type=0
DMI MultiFlash 3.00 [wide=0 sync=0 cmdq=0 sftre=0 pq=0x0]
/dev/sg3: scsi2 channel=0 id=0 lun=3 [em] type=0
DMI MultiFlash 3.00 [wide=0 sync=0 cmdq=0 sftre=0 pq=0x0]
Only the multi flash card reader seems to be detected.
Dmesg output:
Linux version 2.6.18-1.2798.fc6xen (brewbuilder at hs20-bc2-4.build.redhat.com) (gcc version 4.1.1 20061011 (Red Hat 4.1.1-30)) #1 SMP Mon Oct 16 15:11:19 EDT 2006
BIOS-provided physical RAM map:
Xen: 0000000000000000 - 000000003b4b9000 (usable)
220MB HIGHMEM available.
727MB LOWMEM available.
Using x86 segment limits to approximate NX protection
On node 0 totalpages: 242873
DMA zone: 186366 pages, LIFO batch:31
HighMem zone: 56507 pages, LIFO batch:15
found SMP MP-table at 000fe710
DMI 2.3 present.
ACPI: RSDP (v000 DELL ) @ 0x000feba0
ACPI: RSDT (v001 DELL 4600i 0x00000007 ASL 0x00000061) @ 0x000fd1b2
ACPI: FADT (v001 DELL 4600i 0x00000007 ASL 0x00000061) @ 0x000fd1e6
ACPI: SSDT (v001 DELL st_ex 0x00001000 MSFT 0x0100000d) @ 0xfffd1afb
ACPI: MADT (v001 DELL 4600i 0x00000007 ASL 0x00000061) @ 0x000fd25a
ACPI: BOOT (v001 DELL 4600i 0x00000007 ASL 0x00000061) @ 0x000fd2c6
ACPI: DSDT (v001 DELL dt_ex 0x00001000 MSFT 0x0100000d) @ 0x00000000
ACPI: Local APIC address 0xfee00000
ACPI: LAPIC (acpi_id[0x01] lapic_id[0x00] enabled)
ACPI: LAPIC (acpi_id[0x02] lapic_id[0x01] disabled)
ACPI: LAPIC (acpi_id[0x03] lapic_id[0x01] disabled)
ACPI: LAPIC (acpi_id[0x04] lapic_id[0x03] disabled)
ACPI: IOAPIC (id[0x01] address[0xfec00000] gsi_base[0])
IOAPIC[0]: apic_id 1, version 32, address 0xfec00000, GSI 0-23
ACPI: INT_SRC_OVR (bus 0 bus_irq 0 global_irq 2 dfl dfl)
ACPI: INT_SRC_OVR (bus 0 bus_irq 9 global_irq 9 high level)
ACPI: IRQ0 used by override.
ACPI: IRQ2 used by override.
ACPI: IRQ9 used by override.
Enabling APIC mode: Flat. Using 1 I/O APICs
Using ACPI (MADT) for SMP configuration information
Built 1 zonelists. Total pages: 242873
Kernel command line: ro root=LABEL=/1 rhgb quiet
Enabling fast FPU save and restore... done.
Enabling unmasked SIMD FPU exception support... done.
Initializing CPU#0
CPU 0 irqstacks, hard=c078a000 soft=c076a000
PID hash table entries: 4096 (order: 12, 16384 bytes)
Xen reported: 2394.038 MHz processor.
Console: colour VGA+ 80x25
Dentry cache hash table entries: 131072 (order: 7, 524288 bytes)
Inode-cache hash table entries: 65536 (order: 6, 262144 bytes)
Software IO TLB enabled:
Aperture: 2 megabytes
Kernel range: 0x00000000c0c65000 - 0x00000000c0e65000
vmalloc area: ee000000-f4ffe000, maxmem 2d7fe000
Memory: 941724k/971492k available (2097k kernel code, 20692k reserved, 840k data, 180k init, 226028k highmem)
Checking if this processor honours the WP bit even in supervisor mode... Ok.
Calibrating delay using timer specific routine.. 5989.30 BogoMIPS (lpj=11978606)
Security Framework v1.0.0 initialized
SELinux: Initializing.
SELinux: Starting in permissive mode
selinux_register_security: Registering secondary module capability
Capability LSM initialized as secondary
Mount-cache hash table entries: 512
CPU: After generic identify, caps: bfebd3f1 00000000 00000000 00000000 00004400 00000000 00000000
CPU: After vendor identify, caps: bfebd3f1 00000000 00000000 00000000 00004400 00000000 00000000
CPU: Trace cache: 12K uops, L1 D cache: 8K
CPU: L2 cache: 512K
CPU: After all inits, caps: bfebd3f1 00000000 00000000 00000080 00004400 00000000 00000000
Checking 'hlt' instruction... OK.
SMP alternatives: switching to UP code
Freeing SMP alternatives: 12k freed
ACPI: Core revision 20060707
ENABLING IO-APIC IRQs
Brought up 1 CPUs
sizeof(vma)=88 bytes
sizeof(page)=32 bytes
sizeof(inode)=424 bytes
sizeof(dentry)=148 bytes
sizeof(ext3inode)=600 bytes
sizeof(buffer_head)=52 bytes
sizeof(skbuff)=172 bytes
sizeof(task_struct)=1392 bytes
checking if image is initramfs... it is
Freeing initrd memory: 3436k freed
Grant table initialized
NET: Registered protocol family 16
ACPI: bus type pci registered
PCI: Using configuration type 1
Setting up standard PCI resources
Allocating PCI resources starting at 50000000 (gap: 40000000:bec00000)
ACPI: Interpreter enabled
ACPI: Using IOAPIC for interrupt routing
ACPI: PCI Root Bridge [PCI0] (0000:00)
PCI: Probing PCI hardware (bus 00)
ACPI: Assume root bridge [\_SB_.PCI0] bus is 0
PCI quirk: region 0800-087f claimed by ICH4 ACPI/GPIO/TCO
PCI quirk: region 0880-08bf claimed by ICH4 GPIO
PCI: Ignoring BAR0-3 of IDE controller 0000:00:1f.1
Boot video device is 0000:01:00.0
PCI: Firmware left 0000:02:08.0 e100 interrupts enabled, disabling
PCI: Transparent bridge - 0000:00:1e.0
ACPI: PCI Interrupt Routing Table [\_SB_.PCI0._PRT]
ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.PCI1._PRT]
ACPI: PCI Interrupt Link [LNKA] (IRQs 3 4 5 6 7 9 10 *11 12 15)
ACPI: PCI Interrupt Link [LNKB] (IRQs *3 4 5 6 7 9 10 11 12 15)
ACPI: PCI Interrupt Link [LNKC] (IRQs 3 4 5 6 7 *9 10 11 12 15)
ACPI: PCI Interrupt Link [LNKD] (IRQs 3 4 5 6 7 9 *10 11 12 15)
ACPI: PCI Interrupt Link [LNKE] (IRQs 3 4 5 6 7 9 *10 11 12 15)
ACPI: PCI Interrupt Link [LNKF] (IRQs 3 4 5 6 7 9 *10 11 12 15)
ACPI: PCI Interrupt Link [LNKG] (IRQs 3 4 *5 6 7 9 10 11 12 15)
ACPI: PCI Interrupt Link [LNKH] (IRQs 3 4 *5 6 7 9 10 11 12 15)
Linux Plug and Play Support v0.97 (c) Adam Belay
pnp: PnP ACPI init
pnp: PnP ACPI: found 12 devices
xen_mem: Initialising balloon driver.
usbcore: registered new driver usbfs
usbcore: registered new driver hub
PCI: Using ACPI for IRQ routing
PCI: If a device doesn't work, try "pci=routeirq". If it helps, post a report
NetLabel: Initializing
NetLabel: domain hash size = 128
NetLabel: protocols = UNLABELED CIPSOv4
NetLabel: unlabeled traffic allowed by default
pnp: 00:0b: ioport range 0x800-0x85f could not be reserved
pnp: 00:0b: ioport range 0xc00-0xc7f has been reserved
pnp: 00:0b: ioport range 0x860-0x8ff could not be reserved
PCI: Bridge: 0000:00:01.0
IO window: disabled.
MEM window: fd000000-feafffff
PREFETCH window: f0000000-f7ffffff
PCI: Bridge: 0000:00:1e.0
IO window: d000-dfff
MEM window: fcf00000-fcffffff
PREFETCH window: disabled.
PCI: Setting latency timer of device 0000:00:1e.0 to 64
NET: Registered protocol family 2
IP route cache hash table entries: 32768 (order: 5, 131072 bytes)
TCP established hash table entries: 131072 (order: 9, 2621440 bytes)
TCP bind hash table entries: 65536 (order: 8, 1310720 bytes)
TCP: Hash tables configured (established 131072 bind 65536)
TCP reno registered
Simple Boot Flag value 0x87 read from CMOS RAM was invalid
Simple Boot Flag at 0x7a set to 0x1
IA-32 Microcode Update Driver: v1.14-xen <tigran at veritas.com>
audit: initializing netlink socket (disabled)
audit(1167585362.304:1): initialized
highmem bounce pool size: 64 pages
VFS: Disk quotas dquot_6.5.1
Dquot-cache hash table entries: 1024 (order 0, 4096 bytes)
SELinux: Registering netfilter hooks
Initializing Cryptographic API
ksign: Installing public key data
Loading keyring
- Added public key 8BDC589434DBC709
- User ID: Red Hat, Inc. (Kernel Module GPG key)
io scheduler noop registered
io scheduler anticipatory registered
io scheduler deadline registered
io scheduler cfq registered (default)
pci_hotplug: PCI Hot Plug PCI Core version: 0.5
ACPI Exception (acpi_processor-0681): AE_NOT_FOUND, Processor Device is not present [20060707]
ACPI: Getting cpuindex for acpiid 0x2
Real Time Clock Driver v1.12ac
Non-volatile memory driver v1.2
Linux agpgart interface v0.101 (c) Dave Jones
agpgart: Detected an Intel 865 Chipset.
agpgart: AGP aperture is 128M @ 0xe8000000
RAMDISK driver initialized: 16 RAM disks of 16384K size 4096 blocksize
Xen virtual console successfully installed as ttyS0
Event-channel device installed.
Uniform Multi-Platform E-IDE driver Revision: 7.00alpha2
ide: Assuming 33MHz system bus speed for PIO modes; override with idebus=xx
ICH5: IDE controller at PCI slot 0000:00:1f.1
ACPI: PCI Interrupt 0000:00:1f.1[A] -> GSI 18 (level, low) -> IRQ 16
ICH5: chipset revision 2
ICH5: not 100% native mode: will probe irqs later
ide0: BM-DMA at 0xffa0-0xffa7, BIOS settings: hda:DMA, hdb:pio
ide1: BM-DMA at 0xffa8-0xffaf, BIOS settings: hdc:DMA, hdd:DMA
Probing IDE interface ide0...
hda: ST3120026A, ATA DISK drive
ide0 at 0x1f0-0x1f7,0x3f6 on irq 14
Probing IDE interface ide1...
hdc: HL-DT-STDVD-ROM GDR8163B, ATAPI CD/DVD-ROM drive
hdd: SAMSUNG CD-R/RW SW-248F, ATAPI CD/DVD-ROM drive
ide1 at 0x170-0x177,0x376 on irq 15
hda: max request size: 512KiB
hda: 234375000 sectors (120000 MB) w/8192KiB Cache, CHS=16383/255/63, UDMA(100)
hda: cache flushes supported
hda: hda1 hda2 hda3 < hda5 hda6 hda7 hda8 hda9 >
ide-floppy driver 0.99.newide
usbcore: registered new driver libusual
usbcore: registered new driver hiddev
usbcore: registered new driver usbhid
drivers/usb/input/hid-core.c: v2.6:USB HID core driver
PNP: PS/2 Controller [PNP0303:KBD,PNP0f13:MOU] at 0x60,0x64 irq 1,12
serio: i8042 AUX port at 0x60,0x64 irq 12
serio: i8042 KBD port at 0x60,0x64 irq 1
mice: PS/2 mouse device common for all mice
md: md driver 0.90.3 MAX_MD_DEVS=256, MD_SB_DISKS=27
md: bitmap version 4.39
TCP bic registered
Initializing IPsec netlink socket
NET: Registered protocol family 1
NET: Registered protocol family 17
Using IPI No-Shortcut mode
Freeing unused kernel memory: 180k freed
Write protecting the kernel read-only data: 356k
input: AT Translated Set 2 keyboard as /class/input/input0
USB Universal Host Controller Interface driver v3.0
ACPI: PCI Interrupt 0000:00:1d.0[A] -> GSI 16 (level, low) -> IRQ 17
PCI: Setting latency timer of device 0000:00:1d.0 to 64
uhci_hcd 0000:00:1d.0: UHCI Host Controller
uhci_hcd 0000:00:1d.0: new USB bus registered, assigned bus number 1
uhci_hcd 0000:00:1d.0: irq 17, io base 0x0000ff80
usb usb1: configuration #1 chosen from 1 choice
hub 1-0:1.0: USB hub found
hub 1-0:1.0: 2 ports detected
ACPI: PCI Interrupt 0000:00:1d.1[B] -> GSI 19 (level, low) -> IRQ 18
PCI: Setting latency timer of device 0000:00:1d.1 to 64
uhci_hcd 0000:00:1d.1: UHCI Host Controller
uhci_hcd 0000:00:1d.1: new USB bus registered, assigned bus number 2
uhci_hcd 0000:00:1d.1: irq 18, io base 0x0000ff60
usb usb2: configuration #1 chosen from 1 choice
hub 2-0:1.0: USB hub found
hub 2-0:1.0: 2 ports detected
ACPI: PCI Interrupt 0000:00:1d.2[C] -> GSI 18 (level, low) -> IRQ 16
PCI: Setting latency timer of device 0000:00:1d.2 to 64
uhci_hcd 0000:00:1d.2: UHCI Host Controller
uhci_hcd 0000:00:1d.2: new USB bus registered, assigned bus number 3
uhci_hcd 0000:00:1d.2: irq 16, io base 0x0000ff40
usb usb3: configuration #1 chosen from 1 choice
hub 3-0:1.0: USB hub found
hub 3-0:1.0: 2 ports detected
ACPI: PCI Interrupt 0000:00:1d.3[A] -> GSI 16 (level, low) -> IRQ 17
PCI: Setting latency timer of device 0000:00:1d.3 to 64
uhci_hcd 0000:00:1d.3: UHCI Host Controller
uhci_hcd 0000:00:1d.3: new USB bus registered, assigned bus number 4
uhci_hcd 0000:00:1d.3: irq 17, io base 0x0000ff20
usb usb4: configuration #1 chosen from 1 choice
hub 4-0:1.0: USB hub found
hub 4-0:1.0: 2 ports detected
usb 1-1: new full speed USB device using uhci_hcd and address 2
ohci_hcd: 2005 April 22 USB 1.1 'Open' Host Controller (OHCI) Driver (PCI)
ACPI: PCI Interrupt 0000:00:1d.7[D] -> GSI 23 (level, low) -> IRQ 19
PCI: Setting latency timer of device 0000:00:1d.7 to 64
ehci_hcd 0000:00:1d.7: EHCI Host Controller
ehci_hcd 0000:00:1d.7: new USB bus registered, assigned bus number 5
ehci_hcd 0000:00:1d.7: debug port 1
PCI: cache line size of 128 is not supported by device 0000:00:1d.7
ehci_hcd 0000:00:1d.7: irq 19, io mem 0xffa80800
ehci_hcd 0000:00:1d.7: USB 2.0 started, EHCI 1.00, driver 10 Dec 2004
usb usb5: configuration #1 chosen from 1 choice
hub 5-0:1.0: USB hub found
hub 5-0:1.0: 8 ports detected
input: ImPS/2 Logitech Wheel Mouse as /class/input/input1
SCSI subsystem initialized
libata version 2.00 loaded.
ata_piix 0000:00:1f.2: version 2.00
ata_piix 0000:00:1f.2: MAP [ P0 -- P1 -- ]
ACPI: PCI Interrupt 0000:00:1f.2[A] -> GSI 18 (level, low) -> IRQ 16
PCI: Setting latency timer of device 0000:00:1f.2 to 64
ata1: SATA max UDMA/133 cmd 0xFE00 ctl 0xFE12 bmdma 0xFEA0 irq 16
ata2: SATA max UDMA/133 cmd 0xFE20 ctl 0xFE32 bmdma 0xFEA8 irq 16
scsi0 : ata_piix
usb 1-1: device not accepting address 2, error -71
usb 1-1: new full speed USB device using uhci_hcd and address 4
usb 1-1: configuration #1 chosen from 1 choice
libusual: modprobe for usb-storage succeeded, but module is not present
ata1: port is slow to respond, please be patient
ata1: port failed to respond (30 secs)
ata1: SRST failed (status 0xFF)
ata1: SRST failed (err_mask=0x100)
ata1: softreset failed, retrying in 5 secs
ata1: SRST failed (status 0xFF)
ata1: SRST failed (err_mask=0x100)
ata1: softreset failed, retrying in 5 secs
ata1: SRST failed (status 0xFF)
ata1: SRST failed (err_mask=0x100)
ata1: reset failed, giving up
scsi1 : ata_piix
ata2: port is slow to respond, please be patient
ata2: port failed to respond (30 secs)
ata2: SRST failed (status 0xFF)
ata2: SRST failed (err_mask=0x100)
ata2: softreset failed, retrying in 5 secs
ata2: SRST failed (status 0xFF)
ata2: SRST failed (err_mask=0x100)
ata2: softreset failed, retrying in 5 secs
ata2: SRST failed (status 0xFF)
ata2: SRST failed (err_mask=0x100)
ata2: reset failed, giving up
Initializing USB Mass Storage driver...
scsi2 : SCSI emulation for USB Mass Storage devices
usb-storage: device found at 4
usb-storage: waiting for device to settle before scanning
usbcore: registered new driver usb-storage
USB Mass Storage support registered.
Vendor: DMI Model: MultiFlash Rev: 3.00
Type: Direct-Access ANSI SCSI revision: 00
sd 2:0:0:0: Attached scsi removable disk sda
Vendor: DMI Model: MultiFlash Rev: 3.00
Type: Direct-Access ANSI SCSI revision: 00
sd 2:0:0:1: Attached scsi removable disk sdb
Vendor: DMI Model: MultiFlash Rev: 3.00
Type: Direct-Access ANSI SCSI revision: 00
sd 2:0:0:2: Attached scsi removable disk sdc
Vendor: DMI Model: MultiFlash Rev: 3.00
Type: Direct-Access ANSI SCSI revision: 00
sd 2:0:0:3: Attached scsi removable disk sdd
usb-storage: device scan complete
kjournald starting. Commit interval 5 seconds
EXT3-fs: mounted filesystem with ordered data mode.
security: 3 users, 6 roles, 1560 types, 166 bools, 1 sens, 1024 cats
security: 58 classes, 48173 rules
SELinux: Completing initialization.
SELinux: Setting up existing superblocks.
SELinux: initialized (dev hda6, type ext3), uses xattr
SELinux: initialized (dev usbfs, type usbfs), uses genfs_contexts
SELinux: initialized (dev tmpfs, type tmpfs), uses transition SIDs
SELinux: initialized (dev debugfs, type debugfs), uses genfs_contexts
SELinux: initialized (dev selinuxfs, type selinuxfs), uses genfs_contexts
SELinux: initialized (dev mqueue, type mqueue), uses transition SIDs
SELinux: initialized (dev devpts, type devpts), uses transition SIDs
SELinux: initialized (dev eventpollfs, type eventpollfs), uses task SIDs
SELinux: initialized (dev inotifyfs, type inotifyfs), uses genfs_contexts
SELinux: initialized (dev tmpfs, type tmpfs), uses transition SIDs
SELinux: initialized (dev futexfs, type futexfs), uses genfs_contexts
SELinux: initialized (dev pipefs, type pipefs), uses task SIDs
SELinux: initialized (dev sockfs, type sockfs), uses task SIDs
SELinux: initialized (dev cpuset, type cpuset), not configured for labeling
SELinux: initialized (dev proc, type proc), uses genfs_contexts
SELinux: initialized (dev bdev, type bdev), uses genfs_contexts
SELinux: initialized (dev rootfs, type rootfs), uses genfs_contexts
SELinux: initialized (dev sysfs, type sysfs), uses genfs_contexts
audit(1167585455.981:2): policy loaded auid=4294967295
hdc: ATAPI 48X DVD-ROM drive, 256kB Cache, UDMA(33)
Uniform CD-ROM driver Revision: 3.20
hdd: ATAPI 48X CD-ROM CD-R/RW drive, 2048kB Cache, UDMA(33)
e100: Intel(R) PRO/100 Network Driver, 3.5.10-k2-NAPI
e100: Copyright(c) 1999-2005 Intel Corporation
ACPI: PCI Interrupt 0000:02:08.0[A] -> GSI 20 (level, low) -> IRQ 20
e100: eth0: e100_probe: addr 0xfcfef000, irq 20, MAC addr 00:07:E9:49:CF:68
input: PC Speaker as /class/input/input2
ACPI: PCI Interrupt 0000:00:1f.3[B] -> GSI 17 (level, low) -> IRQ 21
ACPI: PCI Interrupt 0000:02:00.0[A] -> GSI 21 (level, low) -> IRQ 22
sd 2:0:0:0: Attached scsi generic sg0 type 0
sd 2:0:0:1: Attached scsi generic sg1 type 0
sd 2:0:0:2: Attached scsi generic sg2 type 0
sd 2:0:0:3: Attached scsi generic sg3 type 0
ACPI: PCI Interrupt 0000:00:1f.5[B] -> GSI 17 (level, low) -> IRQ 21
PCI: Setting latency timer of device 0000:00:1f.5 to 64
intel8x0_measure_ac97_clock: measured 57258 usecs
intel8x0: clocking to 48000
Floppy drive(s): fd0 is 1.44M
FDC 0 is a post-1991 82077
Intel 82802 RNG detected
parport: PnPBIOS parport detected.
parport0: PC-style at 0x378 (0x778), irq 7 [PCSPP,TRISTATE]
lp0: using parport0 (interrupt-driven).
lp0: console ready
ACPI: Power Button (FF) [PWRF]
ACPI: Power Button (CM) [VBTN]
ibm_acpi: ec object not found
md: Autodetecting RAID arrays.
md: autorun ...
md: ... autorun DONE.
device-mapper: ioctl: 4.7.0-ioctl (2006-06-24) initialised: dm-devel at redhat.com
device-mapper: multipath: version 1.0.4 loaded
EXT3 FS on hda6, internal journal
SELinux: initialized (dev tmpfs, type tmpfs), uses transition SIDs
kjournald starting. Commit interval 5 seconds
EXT3 FS on hda8, internal journal
EXT3-fs: mounted filesystem with ordered data mode.
SELinux: initialized (dev hda8, type ext3), uses xattr
kjournald starting. Commit interval 5 seconds
EXT3 FS on hda9, internal journal
EXT3-fs: mounted filesystem with ordered data mode.
SELinux: initialized (dev hda9, type ext3), uses xattr
kjournald starting. Commit interval 5 seconds
EXT3 FS on hda7, internal journal
EXT3-fs: mounted filesystem with ordered data mode.
SELinux: initialized (dev hda7, type ext3), uses xattr
SELinux: initialized (dev ramfs, type ramfs), uses genfs_contexts
NET: Registered protocol family 10
lo: Disabled Privacy Extensions
IPv6 over IPv4 tunneling driver
Adding 2104472k swap on /dev/hda5. Priority:-1 extents:1 across:2104472k
SELinux: initialized (dev binfmt_misc, type binfmt_misc), uses genfs_contexts
process `sysctl' is using deprecated sysctl (syscall) net.ipv6.neigh.lo.base_reachable_time; Use net.ipv6.neigh.lo.base_reachable_time_ms instead.
ADDRCONF(NETDEV_UP): eth0: link is not ready
e100: eth0: e100_watchdog: link up, 100Mbps, full-duplex
ADDRCONF(NETDEV_CHANGE): eth0: link becomes ready
SELinux: initialized (dev rpc_pipefs, type rpc_pipefs), uses genfs_contexts
Bluetooth: Core ver 2.10
NET: Registered protocol family 31
Bluetooth: HCI device and connection manager initialized
Bluetooth: HCI socket layer initialized
Bluetooth: L2CAP ver 2.8
Bluetooth: L2CAP socket layer initialized
Bluetooth: RFCOMM socket layer initialized
Bluetooth: RFCOMM TTY layer initialized
Bluetooth: RFCOMM ver 1.8
Bluetooth: HIDP (Human Interface Emulation) ver 1.1
audit(1167585489.828:3): bool=allow_ypbind val=1 old_val=0 auid=4294967295
eth0: no IPv6 routers present
audit(1167585511.210:4): bool=allow_ypbind val=0 old_val=1 auid=4294967295
SELinux: initialized (dev autofs, type autofs), uses genfs_contexts
SELinux: initialized (dev autofs, type autofs), uses genfs_contexts
audit(1167585512.402:5): avc: denied { node_bind } for pid=2310 comm="nscd" scontext=system_u:system_r:nscd_t:s0 tcontext=system_u:object_r:inaddr_any_node_t:s0 tclass=tcp_socket
Installing knfsd (copyright (C) 1996 okir at monad.swb.de).
SELinux: initialized (dev nfsd, type nfsd), uses genfs_contexts
NFSD: Using /var/lib/nfs/v4recovery as the NFSv4 state recovery directory
NFSD: starting 90-second grace period
audit(1167585520.450:6): avc: denied { node_bind } for pid=2085 comm="dbus-daemon" scontext=system_u:system_r:system_dbusd_t:s0 tcontext=system_u:object_r:inaddr_any_node_t:s0 tclass=tcp_socket
audit(1167585520.450:7): avc: denied { name_connect } for pid=2085 comm="dbus-daemon" dest=111 scontext=system_u:system_r:system_dbusd_t:s0 tcontext=system_u:object_r:portmap_port_t:s0 tclass=tcp_socket
audit(1167585520.450:8): avc: denied { send_msg } for pid=2085 comm="dbus-daemon" saddr=127.0.0.1 src=33078 daddr=127.0.0.1 dest=111 netif=lo scontext=system_u:system_r:system_dbusd_t:s0 tcontext=system_u:object_r:portmap_port_t:s0 tclass=tcp_socket
audit(1167585520.450:9): avc: denied { recv_msg } for pid=2085 comm="dbus-daemon" saddr=127.0.0.1 src=111 daddr=127.0.0.1 dest=33078 netif=lo scontext=system_u:system_r:system_dbusd_t:s0 tcontext=system_u:object_r:portmap_port_t:s0 tclass=tcp_socket
audit(1167585527.518:10): avc: denied { node_bind } for pid=2331 comm="nscd" scontext=system_u:system_r:nscd_t:s0 tcontext=system_u:object_r:inaddr_any_node_t:s0 tclass=tcp_socket
audit(1167585529.058:11): avc: denied { search } for pid=2817 comm="xenstored" name="/" dev=sysfs ino=1 scontext=system_u:system_r:xenstored_t:s0 tcontext=system_u:object_r:sysfs_t:s0 tclass=dir
audit(1167585529.058:12): avc: denied { read } for pid=2817 comm="xenstored" name="dev" dev=sysfs ino=3740 scontext=system_u:system_r:xenstored_t:s0 tcontext=system_u:object_r:sysfs_t:s0 tclass=file
audit(1167585529.058:13): avc: denied { getattr } for pid=2817 comm="xenstored" name="dev" dev=sysfs ino=3740 scontext=system_u:system_r:xenstored_t:s0 tcontext=system_u:object_r:sysfs_t:s0 tclass=file
Bridge firewalling registered
device vif0.0 entered promiscuous mode
audit(1167585530.099:14): dev=vif0.0 prom=256 old_prom=0 auid=4294967295
xenbr0: port 1(vif0.0) entering learning state
xenbr0: topology change detected, propagating
xenbr0: port 1(vif0.0) entering forwarding state
ADDRCONF(NETDEV_UP): peth0: link is not ready
e100: peth0: e100_watchdog: link up, 100Mbps, full-duplex
ADDRCONF(NETDEV_CHANGE): peth0: link becomes ready
device peth0 entered promiscuous mode
audit(1167585531.171:15): dev=peth0 prom=256 old_prom=0 auid=4294967295
xenbr0: port 2(peth0) entering learning state
xenbr0: topology change detected, propagating
xenbr0: port 2(peth0) entering forwarding state
eth0: no IPv6 routers present
audit(1167585573.281:16): avc: denied { node_bind } for pid=2331 comm="nscd" scontext=system_u:system_r:nscd_t:s0 tcontext=system_u:object_r:inaddr_any_node_t:s0 tclass=tcp_socket
audit(1167586966.873:17): avc: denied { node_bind } for pid=2334 comm="nscd" scontext=system_u:system_r:nscd_t:s0 tcontext=system_u:object_r:inaddr_any_node_t:s0 tclass=tcp_socket
nfsd: last server has exited
nfsd: unexporting all filesystems
RPC: failed to contact portmap (errno -5).
audit(1167587048.504:18): bool=allow_ypbind val=1 old_val=0 auid=4294967295
audit(1167587069.937:19): bool=allow_ypbind val=0 old_val=1 auid=4294967295
audit(1167587076.362:20): avc: denied { node_bind } for pid=2331 comm="nscd" scontext=system_u:system_r:nscd_t:s0 tcontext=system_u:object_r:inaddr_any_node_t:s0 tclass=tcp_socket
audit(1167587091.462:21): avc: denied { node_bind } for pid=2331 comm="nscd" scontext=system_u:system_r:nscd_t:s0 tcontext=system_u:object_r:inaddr_any_node_t:s0 tclass=tcp_socket
audit(1167587094.163:22): bool=allow_ypbind val=1 old_val=0 auid=4294967295
audit(1167587115.848:23): bool=allow_ypbind val=0 old_val=1 auid=4294967295
NFSD: Using /var/lib/nfs/v4recovery as the NFSv4 state recovery directory
NFSD: starting 90-second grace period
audit(1167587122.092:24): avc: denied { node_bind } for pid=2331 comm="nscd" scontext=system_u:system_r:nscd_t:s0 tcontext=system_u:object_r:inaddr_any_node_t:s0 tclass=tcp_socket
audit(1167587147.813:25): avc: denied { node_bind } for pid=2085 comm="dbus-daemon" scontext=system_u:system_r:system_dbusd_t:s0 tcontext=system_u:object_r:inaddr_any_node_t:s0 tclass=tcp_socket
audit(1167587147.813:26): avc: denied { name_connect } for pid=2085 comm="dbus-daemon" dest=111 scontext=system_u:system_r:system_dbusd_t:s0 tcontext=system_u:object_r:portmap_port_t:s0 tclass=tcp_socket
audit(1167587147.813:27): avc: denied { send_msg } for pid=2085 comm="dbus-daemon" saddr=127.0.0.1 src=45616 daddr=127.0.0.1 dest=111 netif=lo scontext=system_u:system_r:system_dbusd_t:s0 tcontext=system_u:object_r:portmap_port_t:s0 tclass=tcp_socket
audit(1167587147.813:28): avc: denied { recv_msg } for pid=2085 comm="dbus-daemon" saddr=127.0.0.1 src=111 daddr=127.0.0.1 dest=45616 netif=lo scontext=system_u:system_r:system_dbusd_t:s0 tcontext=system_u:object_r:portmap_port_t:s0 tclass=tcp_socket
audit(1167587163.414:29): avc: denied { write } for pid=4452 comm="pwconv" name="[19693]" dev=pipefs ino=19693 scontext=system_u:system_r:sysadm_passwd_t:s0 tcontext=system_u:system_r:xdm_t:s0-s0:c0.c1023 tclass=fifo_file
audit(1167587163.426:30): avc: denied { write } for pid=4453 comm="nscd" name="[19693]" dev=pipefs ino=19693 scontext=system_u:system_r:nscd_t:s0 tcontext=system_u:system_r:xdm_t:s0-s0:c0.c1023 tclass=fifo_file
nfsd: last server has exited
nfsd: unexporting all filesystems
RPC: failed to contact portmap (errno -5).
NFSD: Using /var/lib/nfs/v4recovery as the NFSv4 state recovery directory
NFSD: starting 90-second grace period
audit(1167587553.296:31): avc: denied { node_bind } for pid=2085 comm="dbus-daemon" scontext=system_u:system_r:system_dbusd_t:s0 tcontext=system_u:object_r:inaddr_any_node_t:s0 tclass=tcp_socket
audit(1167587553.296:32): avc: denied { name_connect } for pid=2085 comm="dbus-daemon" dest=111 scontext=system_u:system_r:system_dbusd_t:s0 tcontext=system_u:object_r:portmap_port_t:s0 tclass=tcp_socket
audit(1167587553.296:33): avc: denied { send_msg } for pid=2085 comm="dbus-daemon" saddr=127.0.0.1 src=52699 daddr=127.0.0.1 dest=111 netif=lo scontext=system_u:system_r:system_dbusd_t:s0 tcontext=system_u:object_r:portmap_port_t:s0 tclass=tcp_socket
audit(1167587553.296:34): avc: denied { recv_msg } for pid=2085 comm="dbus-daemon" saddr=127.0.0.1 src=111 daddr=127.0.0.1 dest=52699 netif=lo scontext=system_u:system_r:system_dbusd_t:s0 tcontext=system_u:object_r:portmap_port_t:s0 tclass=tcp_socket
audit(1167588177.378:35): avc: denied { execmod } for pid=6212 comm="firefox-bin" name="libqfaservices.so" dev=hda7 ino=417257 scontext=user_u:system_r:unconfined_t:s0 tcontext=system_u:object_r:file_t:s0 tclass=file
ISO 9660 Extensions: RRIP_1991A
SELinux: initialized (dev hdd, type iso9660), uses genfs_contexts
usb 2-1: new full speed USB device using uhci_hcd and address 2
usb 2-1: new full speed USB device using uhci_hcd and address 3
usb 2-1: configuration #1 chosen from 1 choice
usbcore: registered new driver usbserial
drivers/usb/serial/usb-serial.c: USB Serial support registered for generic
usbcore: registered new driver usbserial_generic
drivers/usb/serial/usb-serial.c: USB Serial Driver core
drivers/usb/serial/usb-serial.c: USB Serial support registered for Handspring Visor / Palm OS
drivers/usb/serial/usb-serial.c: USB Serial support registered for Sony Clie 3.5
drivers/usb/serial/usb-serial.c: USB Serial support registered for Sony Clie 5.0
visor 2-1:1.0: Handspring Visor / Palm OS converter detected
usb 2-1: Handspring Visor / Palm OS converter now attached to ttyUSB0
usb 2-1: Handspring Visor / Palm OS converter now attached to ttyUSB1
usbcore: registered new driver visor
drivers/usb/serial/visor.c: USB HandSpring Visor / Palm OS driver
usb 2-1: USB disconnect, address 3
visor ttyUSB0: Handspring Visor / Palm OS converter now disconnected from ttyUSB0
visor ttyUSB1: Handspring Visor / Palm OS converter now disconnected from ttyUSB1
visor 2-1:1.0: device disconnected
usb 2-1: new full speed USB device using uhci_hcd and address 4
usb 2-1: configuration #1 chosen from 1 choice
visor 2-1:1.0: Handspring Visor / Palm OS converter detected
usb 2-1: Handspring Visor / Palm OS converter now attached to ttyUSB0
usb 2-1: Handspring Visor / Palm OS converter now attached to ttyUSB1
SCSI device sdc: 244480 512-byte hdwr sectors (125 MB)
sdc: Write Protect is off
sdc: Mode Sense: 43 00 00 00
sdc: assuming drive cache: write through
SCSI device sdc: 244480 512-byte hdwr sectors (125 MB)
sdc: Write Protect is off
sdc: Mode Sense: 43 00 00 00
sdc: assuming drive cache: write through
sdc: sdc1
SELinux: initialized (dev sdc1, type vfat), uses genfs_contexts
hub 2-0:1.0: port 1 disabled by hub (EMI?), re-enabling...
usb 2-1: USB disconnect, address 4
visor 2-1:1.0: device disconnected
visor ttyUSB0: Handspring Visor / Palm OS converter now disconnected from ttyUSB0
visor ttyUSB1: Handspring Visor / Palm OS converter now disconnected from ttyUSB1
usb 2-1: new full speed USB device using uhci_hcd and address 5
usb 2-1: device descriptor read/64, error -71
usb 2-1: device descriptor read/64, error -71
usb 2-1: new full speed USB device using uhci_hcd and address 6
usb 2-1: device descriptor read/64, error -71
usb 2-1: device descriptor read/64, error -71
usb 2-1: new full speed USB device using uhci_hcd and address 7
usb 2-1: device not accepting address 7, error -71
usb 2-1: new full speed USB device using uhci_hcd and address 8
usb 2-1: device not accepting address 8, error -71
usb 5-7: new high speed USB device using ehci_hcd and address 6
usb 5-7: configuration #1 chosen from 1 choice
scsi3 : SCSI emulation for USB Mass Storage devices
usb-storage: device found at 6
usb-storage: waiting for device to settle before scanning
Vendor: SanDisk Model: Cruzer Mini Rev: 0.2
Type: Direct-Access ANSI SCSI revision: 02
SCSI device sde: 2001888 512-byte hdwr sectors (1025 MB)
sde: Write Protect is off
sde: Mode Sense: 03 00 00 00
sde: assuming drive cache: write through
SCSI device sde: 2001888 512-byte hdwr sectors (1025 MB)
sde: Write Protect is off
sde: Mode Sense: 03 00 00 00
sde: assuming drive cache: write through
sde: sde1
sd 3:0:0:0: Attached scsi removable disk sde
sd 3:0:0:0: Attached scsi generic sg4 type 0
usb-storage: device scan complete
SELinux: initialized (dev sde1, type vfat), uses genfs_contexts
usb 5-7: USB disconnect, address 6
usb 5-7: new high speed USB device using ehci_hcd and address 7
usb 5-7: configuration #1 chosen from 1 choice
scsi4 : SCSI emulation for USB Mass Storage devices
usb-storage: device found at 7
usb-storage: waiting for device to settle before scanning
Vendor: SanDisk Model: Cruzer Mini Rev: 0.2
Type: Direct-Access ANSI SCSI revision: 02
SCSI device sde: 2001888 512-byte hdwr sectors (1025 MB)
sde: Write Protect is off
sde: Mode Sense: 03 00 00 00
sde: assuming drive cache: write through
SCSI device sde: 2001888 512-byte hdwr sectors (1025 MB)
sde: Write Protect is off
sde: Mode Sense: 03 00 00 00
sde: assuming drive cache: write through
sde: sde1
sd 4:0:0:0: Attached scsi removable disk sde
sd 4:0:0:0: Attached scsi generic sg4 type 0
usb-storage: device scan complete
SELinux: initialized (dev sde1, type vfat), uses genfs_contexts
SCSI device sdc: 244480 512-byte hdwr sectors (125 MB)
sdc: Write Protect is off
sdc: Mode Sense: 43 00 00 00
sdc: assuming drive cache: write through
SCSI device sdc: 244480 512-byte hdwr sectors (125 MB)
sdc: Write Protect is off
sdc: Mode Sense: 43 00 00 00
sdc: assuming drive cache: write through
sdc: sdc1
SELinux: initialized (dev sdc1, type vfat), uses genfs_contexts
usb 5-7: USB disconnect, address 7
usb 2-2: new full speed USB device using uhci_hcd and address 9
usb 2-2: configuration #1 chosen from 1 choice
usb 2-2: USB disconnect, address 9
nfsd: last server has exited
nfsd: unexporting all filesystems
RPC: failed to contact portmap (errno -5).
usb 2-1: new full speed USB device using uhci_hcd and address 10
usb 2-1: device descriptor read/64, error -71
usb 2-1: device descriptor read/64, error -71
usb 2-1: new full speed USB device using uhci_hcd and address 11
usb 2-1: device descriptor read/64, error -71
usb 2-1: device descriptor read/64, error -71
usb 2-1: new full speed USB device using uhci_hcd and address 12
usb 2-1: device not accepting address 12, error -71
usb 2-1: new full speed USB device using uhci_hcd and address 13
usb 2-1: device not accepting address 13, error -71
audit(1167591879.030:36): avc: denied { execmod } for pid=6212 comm="firefox-bin" name="libflashplayer.so" dev=hda9 ino=1704177 scontext=user_u:system_r:unconfined_t:s0 tcontext=system_u:object_r:file_t:s0 tclass=file
% tail /var/log/messages
Dec 31 13:58:18 gondor kernel: usb 2-1: new full speed USB device using uhci_hcd and address 11
Dec 31 13:58:19 gondor kernel: usb 2-1: device descriptor read/64, error -71
Dec 31 13:58:19 gondor kernel: usb 2-1: device descriptor read/64, error -71
Dec 31 13:58:19 gondor kernel: usb 2-1: new full speed USB device using uhci_hcd and address 12
Dec 31 13:58:19 gondor kernel: usb 2-1: device not accepting address 12, error -71
Dec 31 13:58:20 gondor kernel: usb 2-1: new full speed USB device using uhci_hcd and address 13
Dec 31 13:58:20 gondor kernel: usb 2-1: device not accepting address 13, error -71
Dec 31 14:04:39 gondor kernel: audit(1167591879.030:36): avc: denied { execmod } for pid=6212 comm="firefox-bin" name="libflashplayer.so" dev=hda9 ino=1704177 scontext=user_u:system_r:unconfined_t:s0 tcontext=system_u:object_r:file_t:s0 tclass=file
Dec 31 15:04:39 gondor ntpd[2371]: synchronized to 207.188.193.108, stratum 2
Dec 31 18:56:32 gondor kcheckpass[12288]: Authentication failure for sue (invoked by uid 600)
Any help is greatly appreciated - the iaudio device is acting like it is waiting to be connected.
>
>On Sun, 31 Dec 2006, Susan Macchia wrote:
>> Hi guys,
>>
>> I just upgraded to FC6 (from FC1); really this was a new install.
>>
>> Anyway, on FC1 I could mount my iaudio (30G) mp3 player as a simple
>> usb/scsi device.
More information about the Linux-users
mailing list